Rebar Calculator
Estimate the amount of reinforcement steel (rebar) needed for slabs, beams, columns, and footings — including bar spacing, lap length, weight, and total cost calculation.
Total Bars (Length Direction):
Total Bars (Width Direction):
Total Rebar Length: m
Total Cost:
Whether you are pouring a residential slab, constructing a concrete retaining wall, building a foundation, or setting footings for a structure, getting your rebar layout and quantity right before ordering saves you from costly mid-pour delays, excess material on site, and structural deficiencies that may not surface until years later. A rebar calculator works from your slab or wall dimensions, your required bar spacing, and your bar size to tell you the total linear footage of rebar needed, the number of bars to order, the weight of steel on the truck, and the overlap required at lap splices.
This guide covers the rebar quantity formula, standard bar sizes and weights, spacing requirements for slabs and walls, lap splice lengths, coverage tables for common slab areas, and frequently asked questions about reinforcement estimating.
The Rebar Quantity Formula
Rebar is laid in a grid pattern within the concrete. The total linear footage is calculated by counting the number of bars in each direction and multiplying by the bar length in that direction:
Bars in X direction = (Slab Length / Spacing) + 1
Bars in Y direction = (Slab Width / Spacing) + 1
Total Linear Footage = (Bars in X × Slab Width) + (Bars in Y × Slab Length)
For a 20 ft x 30 ft slab with #4 rebar at 12-inch spacing:
- Bars running lengthwise (30 ft bars): (20 / 1) + 1 = 21 bars × 30 ft = 630 linear feet
- Bars running widthwise (20 ft bars): (30 / 1) + 1 = 31 bars × 20 ft = 620 linear feet
- Total: 630 + 620 = 1,250 linear feet
- Add 10% for lap splices and waste: 1,250 × 1.10 = 1,375 linear feet
Standard Rebar Sizes and Weights
Rebar is designated by bar number, which approximates the diameter in eighths of an inch. Bar weight affects both shipping cost and the structural capacity of the reinforced concrete member.
Bar Size | Diameter (inches) | Area (sq in) | Weight (lb/ft) | Common Application |
#3 | 0.375 | 0.11 | 0.376 | Light slabs, walkways, small footings |
#4 | 0.500 | 0.20 | 0.668 | Residential slabs, walls, footings |
#5 | 0.625 | 0.31 | 1.043 | Commercial slabs, retaining walls |
#6 | 0.750 | 0.44 | 1.502 | Heavy foundations, columns |
#7 | 0.875 | 0.60 | 2.044 | Structural columns, heavy beams |
#8 | 1.000 | 0.79 | 2.670 | Structural members, bridge decks |
#9 | 1.128 | 1.00 | 3.400 | Heavy structural applications |
#10 | 1.270 | 1.27 | 4.303 | Heavy columns, transfer beams |
#11 | 1.410 | 1.56 | 5.313 | Large columns, mat foundations |
Rebar Spacing Requirements
Minimum and maximum rebar spacing is set by ACI 318 and local building codes. Spacing affects both structural capacity and constructability. Bars placed too close together prevent proper concrete consolidation around the steel.
Application | Bar Size | Typical Spacing | Minimum Clear Spacing | Notes |
Residential slab on grade | #3 – #4 | 12 – 18 inches | 1.5 × bar diameter | 6 inches minimum in high-shrinkage zones |
Commercial slab | #4 – #5 | 12 inches | 1.5 × bar diameter | Check with structural engineer |
Basement wall | #4 – #5 | 12 inches vertical, 12 – 16 inches horizontal | 1.5 × bar diameter | Consult engineer for backfill height |
Retaining wall | #5 – #6 | 8 – 12 inches | 1.5 × bar diameter | Vertical bars take bending load |
Column ties | #3 – #4 | 4 – 6 inches | 1.5 × bar diameter | Closer spacing at column ends |
Beam stirrups | #3 – #4 | 6 – 12 inches | 1.5 × bar diameter | Closer spacing near supports |
Footing | #4 – #5 | 12 inches both ways | 1.5 × bar diameter | Both top and bottom mats often required |
Rebar Coverage Table by Slab Area
The table below shows rebar quantities for common slab areas using #4 bar at 12-inch spacing on center, single mat, with a 10 percent waste and splice allowance included. For two-mat slabs (top and bottom steel), double all quantities.
Slab Area (sq ft) | Linear Footage (approx) | Weight (lbs) #4 | 20-ft Bars Needed | Tons of Steel |
100 | 220 | 147 | 11 | 0.07 |
200 | 440 | 294 | 22 | 0.15 |
400 | 880 | 588 | 44 | 0.29 |
600 | 1,320 | 882 | 66 | 0.44 |
800 | 1,760 | 1,176 | 88 | 0.59 |
1,000 | 2,200 | 1,470 | 110 | 0.74 |
1,500 | 3,300 | 2,204 | 165 | 1.10 |
2,000 | 4,400 | 2,939 | 220 | 1.47 |
3,000 | 6,600 | 4,409 | 330 | 2.20 |
5,000 | 11,000 | 7,348 | 550 | 3.67 |
Lap Splice Lengths
When bar lengths must be joined end to end, the overlap (lap splice) transfers the load from one bar to the next through bond with the surrounding concrete. Minimum lap splice length depends on bar size, concrete strength, and whether the splice is in tension or compression.
Bar Size | Tension Lap (3,000 psi concrete) | Tension Lap (4,000 psi concrete) | Compression Lap | Notes |
#3 | 15 inches | 13 inches | 12 inches | Minimum 12 inches always |
#4 | 20 inches | 17 inches | 15 inches | Class B splice adds 30% |
#5 | 25 inches | 22 inches | 19 inches |
|
#6 | 30 inches | 26 inches | 23 inches |
|
#7 | 42 inches | 36 inches | 27 inches |
|
#8 | 48 inches | 41 inches | 30 inches |
|
#9 | 66 inches | 57 inches | 34 inches | Stagger splices recommended |
#10 | 83 inches | 72 inches | 38 inches | Stagger splices required by ACI |
Cover Requirements
Concrete cover over the rebar protects the steel from corrosion and provides fire resistance. Minimum cover distances are set by ACI 318 and must be maintained throughout the pour using plastic chairs, wire supports, or dobies.
- Slab on grade, not exposed to weather: 3/4 inch minimum
- Slab exposed to weather or ground: 1.5 inches minimum
- Walls not exposed to weather: 3/4 inch for #5 and smaller; 1.5 inches for #6 and larger
- Walls exposed to weather: 2 inches
- Footings cast against earth: 3 inches minimum
- Columns and beams not exposed: 1.5 inches for #5 and smaller; 1.5 inches for larger
Related tools and guides: concrete footing calculator, concrete wall calculator and rebaring in concrete.
Frequently Asked Questions
When do I need two mats of rebar instead of one?
Two-mat reinforcement is required whenever the slab or wall experiences bending in
What is the maximum bar length I can order?
Standard stock lengths are 20 feet and 40 feet. Custom lengths up to 60 feet are available from some suppliers for special order. For site access, 20-foot lengths are most manageable. Truck deliveries of 40-foot bars require adequate staging area and turning radius at the job site. Order 20-foot lengths for residential projects unless specific longer spans make the splice penalty significant.
How do I calculate rebar for a circular slab?
For a circular slab, calculate the area using the standard circle area formula (pi times radius squared), then use the same linear footage formula but apply it to the bounding square of the circle. Calculate as if the slab were a square with sides equal to the diameter, then multiply the total linear footage by 0.785 to account for the circular cutoff at the perimeter. Add 15 percent for waste due to the angled bar cuts at the curved edge.
Can I substitute a larger bar at wider spacing for a smaller bar at tighter spacing?
Yes, if the cross-sectional steel area per foot of width is maintained equal or greater. Multiply the bar area by the number of bars per foot (12 divided by spacing in inches) to get square inches of steel per foot. Match this value with the new bar and spacing combination. Always confirm substitutions with the structural engineer of record before changing the specified reinforcement.









